Skip to content

Arch Linux Laptop Tweaks Guide ​

This guide helps improve laptop performance, battery life, and usability on Arch Linux.

1. Prevent Sleep When Lid is Closed ​

To keep your laptop running with the lid closed, modify systemd's configuration.

  • Open a terminal and run:

    bash
    sudo tee -a /etc/systemd/logind.conf << EOF
    HandleSuspendKey=ignore
    HandleSuspendKeyLongPress=ignore
    HandleHibernateKey=ignore
    HandleHibernateKeyLongPress=ignore
    HandleLidSwitch=ignore
    HandleLidSwitchExternalPower=ignore
    HandleLidSwitchDocked=ignore
    EOF
  • Reload the systemd config:

    bash
    sudo systemctl restart systemd-logind

2. Battery Optimization ​

WARNING

Using both tlp and auto-cpufreq together will cause compatibility issues. It is recommended to use one power management tool at a time to avoid conflicts in settings and performance optimization.

auto-cpufreq adjusts CPU frequency and power settings based on system load and battery status, optimizing performance and energy use.

  • Install auto-cpufreq (requires an AUR helper like yay):

    bash
    yay -S auto-cpufreq
  • Test in live mode (observe real-time adjustments without installation):

    bash
    sudo auto-cpufreq --live
  • Enable automatic startup (run at boot for automatic adjustments):

    bash
    sudo auto-cpufreq --install
  • Monitor system over time (observe system behavior without making changes):

    bash
    sudo auto-cpufreq --monitor
  • View CPU statistics:

    bash
    sudo auto-cpufreq --stats
  • Uninstall the service:

    bash
    sudo auto-cpufreq --remove

2.2. TLP (Advanced Power Management) ​

TLP optimizes battery life automatically.

  • Install TLP:

    bash
    sudo pacman -S tlp tlp-rdw
  • Start and enable the service:

    bash
    sudo systemctl enable tlp --now
  • Check TLP status:

    bash
    sudo tlp-stat
  • Optional: For a GUI, install tlpui (requires AUR helper like yay):

    bash
    yay -S tlpui

    Run tlpui to configure TLP with a graphical interface.

2.3. CPU Scaling Governor ​

Optimize your CPU governor to balance performance and power usage, especially on battery-powered devices.

  • Install Dependencies:

    bash
    sudo pacman -S cpupower
  • View Current CPU Governor:

    bash
    cpupower frequency-info

    Or use:

    bash
    cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
  • Set the CPU Governor:

    To set the governor to schedutil (recommended for modern kernels):

    bash
    sudo cpupower frequency-set -g schedutil

    For maximum battery efficiency, use the powersave governor:

    bash
    sudo cpupower frequency-set -g powersave
  • Make the Governor Setting Persistent:

    Open the cpupower configuration file for editing:

    bash
    sudo nano /etc/default/cpupower

    Add or edit the following line:

    bash
    GOVERNOR="schedutil"  # or "powersave"
  • Enable and Start the cpupower Service:

    bash
    sudo systemctl enable cpupower --now
  • Verify the Governor Setting:

    bash
    cpupower frequency-info

3. Adjust Swap Usage (Swappiness) ​

Reduce swap usage to improve performance.

  • Check current swappiness (Default = 60):

    bash
    cat /proc/sys/vm/swappiness
  • Edit the config file:

    bash
    sudo nano /etc/sysctl.conf
  • Set swappiness to 10 for less aggressive swap usage:

    bash
    vm.swappiness=10
  • Apply changes:

    bash
    sudo sysctl -p

4. File System Performance (noatime) ​

Disable file access time writes for better performance, especially on SSDs.

  • Edit /etc/fstab:

    bash
    sudo nano /etc/fstab
  • Add noatime to your root (/) partition options:

    bash
    UUID=<your-disk-UUID> / ext4 defaults,noatime 0 1

Reboot to apply the change.


5. System Monitoring Tools ​

5.1. powertop (Power Consumption Monitor) ​

Monitor and optimize power usage.

  • Install powertop:

    bash
    sudo pacman -S powertop
  • Run in interactive mode:

    bash
    sudo powertop
  • Optimize settings automatically:

    bash
    sudo powertop --auto-tune

5.2. btop or htop (Resource Monitoring) ​

Monitor CPU, memory, and system resources.

  • Install btop:

    bash
    sudo pacman -S btop
  • Install htop:

    bash
    sudo pacman -S htop

Released under the MIT License. Built by harilvfs (aka Hari Chalise).